Ultimate Strength Analysis of Roro Passenger Ship under Combined Global and Local Load Using Nonlinear Finite Element Method

Authors

  • Aulia Windyandari Industrial Technology Department, Vocational School, Diponegoro University, Semarang 50271, Indonesia
  • Eko Julianto Sasono Industrial Technology Department, Vocational School, Diponegoro University, Semarang 50271, Indonesia
  • Solichin Djazuli Said Industrial Technology Department, Vocational School, Diponegoro University, Semarang 50271, Indonesia
  • Ahmad Fauzan Zakki Naval Architecture Department, Engineering Faculty, Diponegoro University, Semarang 50271, Indonesia

DOI:

https://doi.org/10.48048/tis.2022.3968

Keywords:

Ultimate hull girder strength, Nonlinear finite element method, Roro passenger ship, Local and global loads, Ultimate global bending load

Abstract

Since roro passenger ships have specific characteristics in handling cargo with the roll-on-roll-off loading and unloading system that must be equipped with a ramp door. Therefore, it is important to conduct the ultimate strength analysis by considering local loads and global loads to ensure the level of safety and reliability of the ship structure. The aim of this research is focused on the investigation of the structural response and the ultimate strength of the roro passenger ship using the non-linear finite element method. The dynamic explicit method is conducted to estimate the large displacement of the deformed structures such as the hull girders, deck girders and plates. In the structural response analysis, the results shows that maximum stress was occurred on the deck girders due to the sagging bending moment load. In the ultimate strength analysis, it is identified that hydrostatic load have reduced the ultimate strength about 33 %. Otherwise, the ultimate strength is increased about 1 %, in the sagging condition.

HIGHLIGHTS

  • The nonlinear behavior of the roro passenger ship ultimate strength due to the combined global and local load is presented
  • On the hogging condition, the addition of local load (hydrostatic pressure) reduce the roro ship ultimate strength about 33 % compare to the pure global ultimate bending load
  • On the sagging condition, the hydrostatic pressure have slightly increased the ultimate strength around 1 %


GRAPHICAL ABSTRACT

Downloads

Download data is not yet available.

References

A Tatsumi and M Fujikubo. Ultimate strength of container ships subjected to combined hogging moment and bottom local loads part 1: Nonlinear finite element analysis. Mar. Struct. 2020; 69, 102683.

C Wang, J Wu and D Wang. Experimental and numerical investigations on the ultimate longitudinal strength of an ultra large container ship. Ocean Engr. 2019; 192, 106546

C Wang, J Wu and D Wang. Design similar scale model of a 10,000 TEU container ship through combined ultimate longitudinal bending and torsion analysis. App. Ocean Res. 2019; 88, 1-14.

G Shi, D Gao and H Zhou. Analysis of hull girder ultimate strength and residual strength based on IACS CSR-H. Math. Problems in Engr. 2019; 2019, 1-11.

TV Van, P Yang and TD Van. Effect of uncertain factors on the hull girder ultimate vertical bending moment of bulk carriers. Ocean Engr. 2018; 148, 704-17.

MC Xu, ZJ Song and J Pan. Study on influence of nonlinear finite element method models on ultimate bending moment for hull girder. Thin-Walled Strct. 2017; 119, 282-95.

MC Xu and G Soares. Numerical assessment of experiments on the ultimate strength of stiffened panels. Engr. Struct. 2012; 45, 460-71.

S Benson, A Abubakar and RS Dow. A comparison of computational methods to predict the progressive collapse behaviour of a damaged box girder. Engr. Strct. 2013; 48, 266-80.

Z Shu and T Moan. Ultimate hull girder strength of a bulk carrier under combined global and local loads in the hogging and alternate hold loading condition using nonlinear finite element analysis. J. Mar. Sci. Tech. 2012; 17, 94-113.

JM Gordo and CG Soares. Tests on ultimate strength of hull box girders made of high tensile steel. Mar. Strct. 2009; 4, 770-90.

JK Paik, BJ Kim and JK Seo. Methods for ultimate limit state assessment of ships and ship-shaped offshore structures: Part III hull girders. Ocean Engr. 2008; 35, 281-6.

E Qi, W Cui and Z Wan. Comparative study of ultimate hull girder strength of large double hull tankers. Mar. Strct. 2005; 18, 227-49.

Roro vessel “the bridges” in Indonesia archipelago, Available at: https://jurnalmaritim.com/ mengenal-kembali-kapal-roro/, accessed July 2020

A Mansour, D Liu. The principle of naval architecture series: Strength of ships and ocean structures. Society of Naval Architect and Marine Engineer, SNAME, Jersey City, USA, 2008, p. 226.

M Harada, TY Zhu and N Yomamoto. Structural reliability analysis for the assessment of ultimate limit state of ship’s hull-a case study. Int. J. Offshore Polar Eng. 2010; 20, 306-12.

HK Amlashi and T Moan. Ultimate strength analysis of a bulk carrier hull girder under alternate hold loading condition–a case study–part 1: Nonlinear finite element modelling and ultimate hull girder capacity. Mar. Struct. 2008; 21, 327-52.

IACS. Common structural rules for bulk carrier and oil tanker. Indonesia Classification Bureau, Rules for Classification and Construction Vol. XVII, BKI, Jakarta, Indonesia, 2012.

MA Kurniawan, FA Prasetyo, S Komariyah. A comparison of three different water areas and its influence for development of rules regulation. In: Proceedings of the Asian Pacific Technical Exchange and Advisory meeting on Marine structures Conference, Mokpo, Korea. 2016.

Downloads

Published

2022-04-30

Issue

Vol. 19 No. 9 (2022): Trends in Sciences, Volume 19, Number 9, 1 May 2022

Section

Research Articles

License

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.